Standardized management of construction sites, safe and beautiful civilized construction sites are something that every construction site must face. The standard steel bar processing shed on the construction site is one of the protective products in construction safety management. The steel bar processing shed on the construction site generally belongs to order production. The production standards for the steel bar processing shed on the site allow sufficient space and welding equipment for processing and production!

钢筋加工棚制作要求：在建建筑在10米以上，钢筋加工场必须设置防护棚，必须设置双层防砸结构。

Requirements for the production of steel bar processing shed: If the building under construction is more than 10 meters, a protective shed must be set up in the steel bar processing yard, and a double-layer anti impact structure must be set up.

一般是组合式连接，散装发货便于运输。 钢筋棚的搭设还要注意一下几点：

Generally, it is a combination connection, which is easy to transport when shipped loose. The installation of the steel shed should also pay attention to the following points:

1.工具式钢筋加工棚搭设具体尺寸根据现场实际情况确定。

1. The specific size of the tool type steel bar processing shed shall be determined based on the actual situation on site.

2.搭设在塔吊回转半径和建筑物周边的加工车间必须设置双层硬质防护。

2. The processing workshop set up around the turning radius of the tower crane and the building must be equipped with double layer hard protection.

3.加工车间地面需硬化，宜选用砼地面。

3. The ground of the processing workshop needs to be hardened, and concrete ground should be selected.

钢筋加工棚制作方法是什么？钢筋加工棚厂家解析

What is the production method for the steel bar processing shed? Analysis of steel bar processing shed manufacturers

4.加工车间顶部应张挂警示标识和宣传用语的横幅，横幅宽度宜为1m。

4. Safety warning signs and safety propaganda slogans should be hung on the top of the processing workshop, with a width of 1m.

5.工具式钢筋加工棚需在醒目处挂操作规程图牌，图牌的尺寸为：宽×高=2000mm×1000mm。

5. The tool type steel bar processing shed should be prominently hung with an operating procedure diagram board, with a size of: wide × Height=2000mm × 1000mm.

6.各种型材及构配件规格为参考值，具体规格应根据当地风荷载、雪荷载进行核算。 7.南方地区，如遇台风应采取防风措施，可设置缆风绳。

6. The specifications of various profiles and components are reference values, and the specific specifications should be calculated based on local wind and snow loads. 7. In the southern region, if encountering a typhoon, wind prevention measures should be taken and cable ropes can be set up.

钢筋加工防护棚制作方法：

Production method of steel bar processing protective shed:

1.构件组装而成，采用封闭式防护，防护性能高，双层防护，有效缓冲高空坠落冲击力。

1. The components are assembled and adopt closed protection, with high safety protection performance and double layer protection, effectively buffering the impact of high-altitude falls.

2.采用国标钢材制作，坚固牢靠、经久耐用。

2. Made of national standard steel, it is sturdy, reliable, and durable.

3.全自动高温烤漆，3年日晒雨林不易褪色。

3. Fully automatic high-temperature baking paint, which is resistant to fading in the 3-year sun exposure rainforest.

4.拼装式，快速组装，拆卸简单，方便运输。

4. Assembly type, fast assembly, simple disassembly, and convenient transportation.

5.款式、颜色、尺寸可根据客户要求定制；

5. The style, color, and size can be customized according to customer requirements;

6.地面需要硬化，立柱基础浇筑700*700*700mm混凝土，预埋300*300*12mm钢板.

6. The ground needs to be hardened, and the column foundation is poured with 700 * 700 * 700mm concrete, and 300 * 300 * 12mm steel plates are embedded

7.各种型材及配件规格可按工地所在地的安防标准定制。

7. Various profiles and accessory specifications can be customized according to the security standards of the construction site.

钢筋棚的搭设还要注意以下几点：

The installation of the steel reinforcement shed should also pay attention to the following points:

1. 工具式钢筋加工棚搭设具体尺寸根据现场实际情况确定；

1. The specific size of the tool type steel bar processing shed shall be determined based on the actual situation on site;

2. 搭设在塔吊回转半径和建筑物周边的加工车间必须设置双层硬质防护；

2. The processing workshop set up around the turning radius of the tower crane and the building must be equipped with double layer hard protection;

3. 加工车间地面需硬化，宜选用砼地面；

3. The ground of the processing workshop needs to be hardened, and concrete ground should be selected;

4. 加工车间顶部应张挂警示标识和宣传用语的 横幅，横幅宽度宜为1m；

4. Safety warning signs and safety propaganda slogans should be hung on the top of the processing workshop, with a width of 1m;

5. 工具式钢筋加工棚需在醒目处挂操作规程图牌，图牌 的尺寸为：宽×高=2000mm×1000mm；

5. The tool type steel bar processing shed should be prominently hung with an operating procedure diagram board, with a size of: wide × Height=2000mm × 1000mm;

6. 各种型材及构配件规格为参考值，具体规格应根据当 地风荷载、雪荷载进行核算；

6. The specifications of various profiles and components are reference values, and the specific specifications should be calculated based on local wind and snow loads;

7. 南方地区，如遇台风应采取防风措施，可设置缆风绳。

7. In the southern region, if encountering a typhoon, wind prevention measures should be taken and cable ropes can be set up.

钢筋加工棚制作方法是什么？钢筋加工棚厂家解析

What is the production method for the steel bar processing shed? Analysis of steel bar processing shed manufacturers

在建筑施工现场工作，工人们经常需要在现场对各种所需的建筑材料进行加工，为了防止高空落物误伤作业人员，保障地面加工作业人员的作业，在施工现场会建起防护棚，现有的防护棚的搭建一部分是通过焊接，搭建完成后不易拆卸，拆卸时需要破坏防护棚的一些结构，使钢筋加工棚不能重复使用，造成经济浪费，防护棚搭建时耗时长，施工麻烦，现有的防护棚使用时对高空落物的冲击力不能有效的消减。

At the construction site, workers often need to process various required building materials on site. In order to prevent high-altitude falling objects from injuring workers and ensure the safety of ground processing workers, protective sheds will be built on the construction site. Part of the existing protective sheds are built through welding, which is not easy to disassemble after completion. Some structures of the protective sheds need to be damaged during disassembly, The reinforcement processing shed cannot be reused, resulting in economic waste. The construction of the protective shed takes a long time and is troublesome. The existing protective shed cannot effectively reduce the impact of high-altitude falling objects when used.

本文由钢筋加工棚为您提供，我们的网站是://www.hongdaxinwuliu.com我们将以全心全意的热情为您提供服务，欢迎您的访问！

This article is provided by the steel bar processing shed, and our website is: //www.hongdaxinwuliu.com We will provide you with wholehearted enthusiasm and welcome your visit!